Kinderkraft I BOOST 2 PRO pink car booster seat

-Kinderkraft I BOOST 2 PRO -car booster seat -for children 125 to 150 cm tall -ISOFIX installation and three-point vehicle seat belt -can also be installed using only the three-point seat belt -removable cover -armrests and belt guides -ex-display condition, very good; packaging may be damaged or replaced The Kinderkraft I BOOST 2 PRO in Pink is a car booster seat for children 125 to 150 centimeters tall. With this model, the child is secured using the vehicle’s three-point seat belt. The instructions specify installation using ISOFIX and the seat belt, or using the seat belt alone, in seats approved by the vehicle manufacturer. The wide seat has foam padding, and the armrests provide a place to rest the arms. The guides help position the lap section of the belt as described in the instructions. The 3D mesh fabric and AIR FLOW system support airflow through the upholstery. The removable cover makes care easier. The upper part of the seat is pink, while the base is dark. Before every journey, check that the booster seat is secured and that the belt is positioned correctly. Care and safety Remove the cover and wash it with mild detergent on a delicate cycle at up to 30°C, following the care label. Do not spin-dry or tumble-dry. Clean the plastic parts with soapy water. Do not use solvents or harsh cleaning products. 4 2.0 Safety instructions Please take a few minutes to read these instructions to ensure your child’s safety. • DO NOT install the car seat on vehicle seats that face backwards or sideways to the direction of travel. • The car seat may be installed only if the seat has a 3-point seat belt. • When installing the car seat on the front seat, the front airbag must be deactivated. • It is recommended that the car seat be installed only on the rear seats of the vehicle. 5 !WARNINGS! Please take a few minutes to read these instructions to ensure your child’s safety. Many easily avoidable injuries are caused by careless and improper use of the car seat. ! The car seat is intended for installation only on vehicle seats that face forward in the direction of travel. Do not install the car seat on vehicle seats/benches that face backwards or sideways to the direction of travel. ! When installing the car seat on the front seat, the front airbag must be deactivated. It is recommended that the car seat be installed only on the rear seats of the vehicle. For information on whether a vehicle seat is suitable for use with a child car seat, refer to the vehicle owner’s manual. ! Make sure the internal harness straps securing the child are adjusted to fit their body and are not twisted. For this reason, do not put thick clothing on your child under the harness. ! The car seat must not be modified in any way without the approval of the relevant type-approval authority. Failure to install the car seat according to the manufacturer’s instructions may endanger life and health. ! Protect the child car seat from direct sunlight, as heated parts may burn your child. Protect your child and the car seat from sunlight. ! Never leave your child unattended in the car seat. ! Make sure that luggage and other objects are adequately secured, especially on the shelf beneath the rear window, as they may cause injury in the event of a collision. ! The car seat must not be used without its cover. ! Do not use replacement covers other than those recommended by the manufacturer, as the cover is an integral part of the car seat’s safety system. ! It is recommended that you keep the car seat instructions for the entire period of use. 6 ! The lap belts of the seat belt must lie as low as possible across your child’s pelvis to provide optimum protection in the event of an accident. ! Replace the car seat if it has been subjected to the severe forces involved in a road accident. ! All hard components and plastic parts of the child car seat must be positioned and installed so that, under normal vehicle operating conditions, they cannot become trapped by a movable seat or vehicle door. ! Regularly check the condition of the car seat, paying particular attention to the attachment points, seams, and adjustment components. Make sure all mechanical components are fully functional. Never lubricate or oil any parts of the child car seat. ! Stop using the car seat if any of its parts are damaged or loose. ! Before every car journey, make sure the car seat is correctly secured. ! Do not use any attachment points other than those described in the instructions and marked on the car seat. ! When an emergency occurs, it is important to unfasten the seat belt quickly. This means the harness release button is not fully secured, so make sure your child does not play with the harness. ! Set a good example for your child and always wear your seat belt. An adult who is not wearing a seat belt can also pose a risk to the child. ! Secure the car seat even when it is not in use. An unsecured car seat can cause passenger injuries even during emergency braking. ! With some vehicle seats made from delicate materials, using a car seat may leave marks and/or cause discoloration. To prevent this, you can place a blanket, towel, or similar item underneath the car seat. 7 IMPORTANT! Make sure there are no gaps between the car seat and the vehicle seat. IMPORTANT! For your child’s comfort, move the front seat as far forward as possible to provide legroom for the child. FAQ What height is this booster seat suitable for? The I BOOST 2 PRO instructions specify a height range of 125 to 150 cm. Can it be used without ISOFIX? The instructions allow installation using only the vehicle’s three-point seat belt, in an approved seating position and in accordance with the instructions. Is the cover removable? Yes. The cover can be removed and gently washed at up to 30°C, following the instructions and care label. Specifications Dispatch time: 24 hours Safety documents I BOOST 2 PRO instructions and manufacturer information: https://kinderkraft.pl/media/wysiwyg/manual/Kinderkraft-I-BOOST-2-PRO-manual-PL.pdf